Figure 1: Berl saddle (left) vs Intalox-style saddle (right) — the notches and rounded lobes are what change the hydraulics, not just the name.
When buyers search intalox saddle ring, they usually mean one of two things: the original Norton-style saddle packing, or the broader family of plastic saddle rings used in scrubbers, absorbers and cooling towers. The confusion starts with naming — "Berl" and "Intalox" sound like materials or brands, but they're geometry generations. This article separates the terminology, puts the measurable differences on one table, and tells you which one to specify for a given duty.
Engineer's Brief: Don't buy on the name — buy on the numbers. The deciding parameters are specific surface area, void fraction, dry packing factor (Fp), and how the shape behaves under your actual liquid load. Berl is acceptable where cost dominates; Intalox-style wins where you need throughput, anti-clogging and stable long-term ΔP.
Both shapes can be made in ceramic, metal or plastic. This article focuses on plastic (PP, PVC, CPVC, PVDF) because that's where the naming mix-up costs buyers the most money.
| Feature | Berl Saddle | Intalox-Style Saddle |
|---|---|---|
| Profile | Simple curved flange, two faces | Asymmetric lobes, rounded edges, side notches |
| Nesting tendency | Higher — pieces interlock | Lower — point contact, more open bed |
| Void fraction (typical) | ~78–82% | ~90–97% (size dependent) |
| Specific surface area | Moderate | Comparable or slightly higher in standard version |
| Stagnant zones | More (concave surfaces) | Fewer (notched, open flow paths) |
| Scaling / fouling | More prone to dead-corner buildup | Better self-flushing, common in desulfurization |
| Mechanical fragility | Sharp flanges can chip (ceramic) | Rounded edges, better integrity |
Geometry comparison based on manufacturer literature and published packing comparisons [2,5](@ref). Values are typical ranges, not a substitute for FXSINO batch test data.
Figure 2: Intalox-style saddle ring — the open arc and notched edges are what keep the bed from collapsing into nested clusters.
| Size (mm) | Specific Area (m²/m³) | Void Fraction (%) | Bulk Density (kg/m³) | Pieces/m³ | Dry Fp (m⁻¹) |
|---|---|---|---|---|---|
| 25 × 12.5 × 1.2 | 288 | 84–85 | ~102 | 97,680 | 473 |
| 38 × 19 × 1.2 | 265 | 95 | ~63 | 25,200 | 405 |
| 50 × 25 × 1.5 | 250 | 96 | ~75 | 9,400 | 332 |
| 76 × 38 × 2.6–3.0 | 200 | 97 | ~59 | 3,700 | 289 |
Data compiled from multiple plastic saddle-ring suppliers; representative of standard Intalox-style geometry [3,7,9](@ref). Berl saddle parameters are less standardized and vary by legacy supplier — request a datasheet before specifying.

Two findings matter, and they don't fully agree — so read carefully:
| If your duty is… | Choose | Reason |
|---|---|---|
| Legacy tower, low budget, mild service | Plastic Berl saddle | Proven, cheap, adequate when ΔP isn't critical |
| Scrubber / desulfurization with slurry or solids | Intalox-style (PP/RPP) | Anti-nesting, self-flushing, slower scaling |
| Low-pressure-drop absorption, large tower | Super Intalox saddle | Half the dry Fp, high flood capacity |
| High mass-transfer area needed (stripping, fine separation) | Standard Intalox saddle | Higher surface area per volume |
| Hot, strongly acidic, abrasive | Ceramic Intalox saddle | Heat + acid resistance beyond plastic envelope |
| Corrosive + moderate temp, want metal-like life | Metal Super Raschig or metal Intalox | Stronger, better for vacuum/distillation |
Q1: Is "Intalox saddle ring" a generic term I can use on a quote?
A: Use "Intalox-style saddle ring" or "saddle ring (Intalox type)" on commercial documents. "Intalox" is a legacy trade style; describing the geometry is safer and still universally understood.
Q2: Which has lower pressure drop, Berl or Intalox?
A: It depends. Small-scale tests show Berl can edge out standard Intalox on raw ΔP; Super-Intalox geometries beat both at larger sizes and higher throughput. Always check the dry packing factor (Fp) and run a pressure drop calculation for your duty.
Q3: Can I replace Berl saddles with Intalox-style in an existing tower?
A: Usually yes, same nominal size. You'll likely gain capacity and anti-clogging behavior, but verify bed height, support grid opening, and distributor coverage. Don't assume "bigger void = automatically better" — confirm the mass-transfer duty still meets spec.
FXSINO supplies plastic Intalox-style saddle rings (PP / PVC / CPVC / PVDF) in 25–76 mm, plus Super Intalox versions and matching distributors. Send tower ID, service fluid, temperature, liquid load and allowable ΔP — we'll return a parameter table and a side-by-side Berl vs Intalox recommendation.
Email: jackieqiu9202@gmail.com | +86 18507999558